National Instruments NI PXIe-8133 Скачать руководство пользователя | Manualshive

Страница: 69 / 92

background image

©

National Instruments

5-1

NI PXIe-8133 User Manual

5

Troubleshooting

This chapter answers common troubleshooting questions you may have
when using the NI PXIe-8133 embedded computer.

What if the NI PXIe-8133 does not boot?

Several problems can cause a controller not to boot. Here are some things
to look for and possible solutions.

Things to Notice

:

•

Which LEDs come on? The

PWROK/FAULT

LED should stay lit

green. The

Drive

LED should blink during boot as the disk is

accessed.

•

What appears on the display? Does it hang at some particular point
(BIOS, Operating System, and so on)? If nothing appears on the
screen, try a different monitor. Does your monitor work with a
different PC? If it hangs, note the last screen output that you saw for
reference when consulting National Instruments technical support.

•

What has changed about the system? Did you recently move the
system? Was there electrical storm activity? Did you recently add
a new module, memory chip, or piece of software?

•

Refer to your chassis user manual for additional troubleshooting steps.

Things to Try

:

•

Make sure the chassis is plugged in to a working power source.

•

Check any fuses or circuit breakers in the chassis or other power
supply (possibly a UPS).

•

Make sure the controller module is firmly seated in the chassis.

•

Remove all other modules from the chassis.

•

Remove any nonessential cables or devices.

•

Try the controller in a different chassis.

•

Try a similar controller in this same chassis.

•

Clear the CMOS. (Refer to the

System CMOS

section of Chapter 2,

Installation and Configuration

.)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
67
68
69
70
71
...
»

Содержание NI PXIe-8133





























































































Отзывы:

Нет отзывов

Похожие инструкции для NI PXIe-8133

Бренд: Salus Страницы: 16

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

Бренд: NEC Страницы: 6

Бренд: Hama Страницы: 8

Бренд: Delta Electronics Страницы: 1

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

Бренд: Renesas Страницы: 2

RanaSystems 13-0010--001

Бренд: RANA Systems Страницы: 328

Бренд: SYNTEK Страницы: 41

DEEP LEARNING PLUS

Бренд: Concept Pro Страницы: 28

Бренд: Active Communications Страницы: 10

Бренд: Softing Страницы: 16

DAS-1800HR Series

Бренд: Keithley Страницы: 139

Бренд: CAME Страницы: 32

Бренд: National Instruments Страницы: 121

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды