National Instruments NI PXIe-8133 Скачать руководство пользователя | Manualshive

Страница: 30 / 92

background image

Chapter 2

Installation and Configuration

©

National Instruments

2-13

NI PXIe-8133 User Manual

•

Device Mode

—This setting enables alternate modes of operation for

the parallel port. Usually the default setting works for all applications.
The default is

STD Printer Mode

.

LabVIEW RT Menu

Use this menu to configure boot options for LabVIEW RT if it is installed
on the controller. If you are not using LabVIEW RT, you should leave these
settings at default.

Note

The settings below override the behavior of the switches shown in Figure 2-4. Refer

to the

LabVIEW RT Configuration Switches

section for more information. To use the

settings from the switches, select

Use Switch Setting

for each option.

•

Boot Configuration

—This setting selects whether the controller

should boot LabVIEW RT, LabVIEW RT Safe Mode, or an installed
OS such as Windows 7. The default is

Use Switch Setting

.

•

Reset IP Address

—If the controller is deployed to a different subnet

from which it was originally configured, or if the current IP address is
invalid, use this switch to reset the IP address and other TCP/IP
settings to their factory defaults during LabVIEW RT startup. The
default is

Use Switch Setting

.

Note

By default, the target will automatically attempt to connect to the network using

DHCP. If the target is unable to initiate a DHCP connection, the target connects to the
network with a link-local IP address or

169.254.x.x

.

•

Disable Startup VI

—If the controller becomes inaccessible because

of a startup VI, this switch can prevent VIs from automatically running
at startup. The default is

Use Switch Setting

.

•

LabVIEW RT Configuration Overrides

—Use this setting to access

the

LabVIEW RT Configuration Overrides

submenu. Refer to the

LabVIEW RT Configuration Overrides Submenu

section for more

information.

Current Hardware Switch Settings

This submenu displays the current values of the LabVIEW RT
configuration switches, indicating Boot Configuration, Reset IP Address,
and Disable Startup VI switch status. For more information on these
settings and the switches that control them, refer to the

LabVIEW RT

Configuration Switches

section of this chapter.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
28
29
30
31
32
...
»

Содержание NI PXIe-8133





























































































Отзывы:

Нет отзывов

Похожие инструкции для NI PXIe-8133

Бренд: Barracuda Networks Страницы: 2

Бренд: dbx Страницы: 8

IntelliJack NJ200

Бренд: 3Com Страницы: 4

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: Salusfin Страницы: 6

Power Control Processor

Бренд: ETC Страницы: 64

Core 2 Quad Q9400

Бренд: Intel Страницы: 2

PCH1 T P Series

Бренд: Parker Страницы: 107

Бренд: Idis Страницы: 20

UniFi LED ULED-AT

Бренд: Ubiquiti Страницы: 16

Бренд: ekwb Страницы: 11

Бренд: SilverStone Страницы: 28

Masterliquid ML240L RGB

Бренд: Cooler Master Страницы: 18

Бренд: HMS Страницы: 18

DTS 4020.timebridge

Бренд: Mobatime Страницы: 94

MICROSPACE MSEBX800

Бренд: DIGITAL-LOGIC Страницы: 53

Бренд: Lanner Страницы: 43

Бренд: Behringer Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды