National Instruments NI PXIe-8133 Скачать руководство пользователя

Страница: 82 / 92

Glossary

National Instruments

G-3

NI PXIe-8133 User Manual

EPP

Enhanced Parallel Port.

expansion ROM

An onboard EEPROM that may contain device-specific initialization and
system boot functionality.

FCC

Federal Communications Commission.

1. Grams.
2. A measure of acceleration equal to 9.8 m/s

GPIB

General Purpose Interface Bus (IEEE 488).

rms

A measure of random vibration—The root mean square of acceleration
levels in a random vibration test profile.

Hertz—Cycles per second.

I/O

Input/Output—The techniques, media, and devices used to achieve
communication between machines and users.

IDE

Integrated Drive Electronics—Hard disk and built-in controller.

IEEE

Institute of Electrical and Electronics Engineers.

in.

Inches.

instrument driver

A set of routines designed to control a specific instrument or family of
instruments, and any necessary related files for LabWindows/CVI or
LabVIEW.

interrupt

A means for a device to request service from another device.

interrupt level

The relative priority at which a device can interrupt.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание NI PXIe-8133





























































































Результаты поиска

Содержание NI PXIe-8133

Отзывы:

Похожие инструкции для NI PXIe-8133

Бренды по названию

Популярные бренды

National Instruments NI PXIe-8133, Руководство пользователя

Результаты поиска

Содержание NI PXIe-8133

Отзывы:

Похожие инструкции для NI PXIe-8133

Бренды по названию

Популярные бренды