National Instruments NI PXIe-8133 Скачать руководство пользователя | Manualshive

Страница: 28 / 92

background image

Chapter 2

Installation and Configuration

©

National Instruments

2-11

NI PXIe-8133 User Manual

•

Reserved I/O

—This setting determines the amount of I/O space, in

bytes, that will be reserved by the BIOS for PCI-PCI bridges that may
be hot-plugged in the ExpressCard slot. The default value for this
setting is

4K

bytes of I/O space.

USB Configuration Submenu

Use this submenu to apply alternate configurations to the USB ports.
Normally, you do not need to modify these settings, as the factory default
settings provide the most compatible and optimal configuration possible.

•

USB Devices

—This item lists the total number of devices detected in

the system, categorized by device type.

•

Legacy USB Support

—This setting specifies whether or not legacy

USB support is enabled. Legacy USB support refers to the ability to
use a USB keyboard and mouse during system boot or in a legacy
operating system such as DOS. The default value is

Enabled

.

Note

Certain real-time applications may require you to disable this setting to reduce loop

time jitter. When the controller is configured to boot LabVIEW RT, legacy USB support is
automatically disabled.

•

Overcurrent Reporting

—This setting allows the BIOS to notify the

operating system of any USB ports which source too much current.
The default value for this setting is

Disabled

.

•

Transfer Timeout

—This setting specifies the timeout value for

Control, Bulk, and Interrupt USB transfers. The default value for this
setting is

20

seconds.

•

Device Reset Timeout

—This setting specifies the number of seconds

the Power-On Self Test will wait for a USB mass storage device to
start. The default is

20

seconds.

•

Device Power-up Delay

—This setting specifies the maximum time a

device will take before it properly reports itself to the host controller.
When set to

Auto

, a root port is granted 100 ms, and for a hub port, the

delay value is taken from the hub descriptor. The default value for this
setting is

Auto

.

•

Device Power-Up Delay in Seconds

—This setting specifies the

number of seconds the Power-On Self Test will wait for a USB device
or hub to power on. This setting is only visible if

Device Power-Up

Delay

is set to

Manual

. The default is

5

seconds.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
26
27
28
29
30
...
»

Содержание NI PXIe-8133





























































































Отзывы:

Нет отзывов

Похожие инструкции для NI PXIe-8133

Бренд: Magnat Audio Страницы: 2

Бренд: Quatech Страницы: 27

Бренд: Salus Страницы: 16

Бренд: Salto Страницы: 2

Бренд: Cypress Semiconductor Страницы: 9

MegaRAID SCSI 320-2X

Бренд: LSI Страницы: 4

ER3-100 (5K02-55)

Бренд: 8e6 Technologies Страницы: 74

DM/IP601-CPCI-100BT

Бренд: Dialogic Страницы: 2

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Бренд: VCS Страницы: 118

F-Tile SDI II Intel Agilex

Бренд: Intel Страницы: 39

Бренд: ETAS Страницы: 82

Бренд: ICP Страницы: 68

Бренд: XtendLan Страницы: 21

Бренд: Ariesys Страницы: 10

Бренд: ATTO Technology Страницы: 2

Hotwire 5620 RTU

Бренд: Paradyne Страницы: 20

Бренд: Radio Shack Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды