National Instruments NI PXIe-8133 Скачать руководство пользователя | Manualshive

Страница: 65 / 92

background image

Chapter 4

Common Configuration Questions

NI PXIe-8133 User Manual

4-4

ni.com

How do I install software from a CD?

The compact size of the NI PXIe-8133 does not allow for an integrated
USB CD/DVD-ROM drive. If you are using Windows 7 or Windows XP,
you have the following options:

•

USB CD/DVD-ROM

—Windows 7 and Windows XP support

installing from a USB CD/DVD-ROM using a bootable installation
CD.

•

SCSI CD-ROM

—Windows 7 and Windows XP supports installing

from a SCSI CD-ROM using a bootable installation CD.

•

Mapped network drive

—You can use the Ethernet to connect to

another computer. If you share the USB CD/DVD-ROM drive on the
other computer, you can map the shared USB CD/DVD-ROM drive to
a drive letter on the NI PXIe-8133.

A USB CD/DVD-ROM drive is available from National Instruments,
part number 778492-01.

Upgrade Information

How do I upgrade system memory?

You can change the amount of installed RAM on the NI PXIe-8133 by
upgrading the DDR3 SO-DIMMs.

To upgrade the RAM, remove the NI PXIe-8133 from the PXI Express
chassis. To optimize both memory capacity and system performance, use
the same size and speed memory module in each of the two module slots.
The use of different size modules in each slot is supported, but system
performance will be slower than using two matched modules. However,
two mismatched modules will result in better performance than using a
single module.

National Instruments offers the following types of SO-DIMMs for use with
the NI PXIe-8133 controller.

•

PC3-10600 (DDR3 1333) 2 GB, 256 MB

×

64, CL 9, 1.18 in. max

(NI part number 781403-2048)

•

PC3-10600 (DDR3 1333) 4 GB, 512 MB

×

64, CL 9, 1.18 in. max

(NI part number 781404-4096)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
63
64
65
66
67
...
»

Содержание NI PXIe-8133





























































































Отзывы:

Нет отзывов

Похожие инструкции для NI PXIe-8133

Бренд: Patton electronics Страницы: 8

Z3-DM8168-PCI-RPS

Бренд: Z3 Technology Страницы: 20

Z3-DM8107-SDI2-RPS

Бренд: Z3 Technology Страницы: 75

Бренд: Z-Wave Страницы: 13

Бренд: Paradyne Страницы: 1

Бренд: Maxim Страницы: 14

Compact Emulator M30620T-CPE

Бренд: Renesas Страницы: 52

Бренд: EVS Страницы: 30

Бренд: SIIG Страницы: 6

Бренд: Teletronics International Страницы: 57

Бренд: AOpen Страницы: 18

EK-FC980 GTX Classy

Бренд: ekwb Страницы: 2

Бренд: Logicube Страницы: 56

Бренд: Datum Страницы: 49

Бренд: Echo Страницы: 21

Бренд: Xilinx Страницы: 27

Gen3 Ethernet Module

Бренд: NCD Страницы: 18

Бренд: ZALMAN Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды