National Instruments NI PXIe-8133 Скачать руководство пользователя | Manualshive

Страница: 29 / 92

background image

Chapter 2

Installation and Configuration

NI PXIe-8133 User Manual

2-12

ni.com

In addition, the following option is available for each detected device if a
USB mass storage device is present:

•

Emulation Type

—This setting specifies how the BIOS will present

the USB mass storage device to the system. This option can be used to
present a USB mass storage device as a floppy, Zip, hard disk, or
CD-ROM drive. The default is

Auto

, which allows the BIOS to treat

small USB flash disk drives as floppy drives and larger USB flash disk
drives as hard disk drives.

Serial/Parallel Port Configuration Submenu

Use this submenu to apply alternate configurations to the serial and
parallel ports. Normally, you do not need to modify these settings, as the
factory default settings provide the most compatible and optimal
configuration possible.

•

Serial Port Configuration

—Use this setting to access the

Serial Port

Configuration

submenu. Refer to the

Serial Port Configuration

Submenu

section for more information.

•

Parallel Port Configuration

—Use this setting to access the

Parallel

Port Configuration

submenu. Refer to the

Parallel Port

Configuration Submenu

section for more information.

Serial Port Configuration Submenu

•

Serial Port

—This setting enables or disables the onboard serial port.

The default value is

Enabled

.

•

Device Settings

—This item displays the current base address and

interrupt request level (IRQ) information for the onboard serial port.

•

Change Settings

—This setting changes the base address and interrupt

request level (IRQ) information for the onboard serial port. The default
value is

Auto

.

Parallel Port Configuration Submenu

•

Parallel Port

—This setting enables or disables the onboard parallel

port. The default value is

Enabled

.

•

Device Settings

—This item displays the current base address and

interrupt request level (IRQ) information for the onboard parallel port.

•

Change Settings

—This setting changes the base address and interrupt

request level (IRQ) information for the onboard parallel port. The
default value is

Auto

. Note that the options available vary based upon

the

Device Mode

selected for the parallel port.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
27
28
29
30
31
...
»

Содержание NI PXIe-8133





























































































Отзывы:

Нет отзывов

Похожие инструкции для NI PXIe-8133

Бренд: IEI Technology Страницы: 21

Бренд: National Instruments Страницы: 9

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

EK-FC780 GTX Jetstream

Бренд: ekwb Страницы: 2

Бренд: Roland Страницы: 12

ACC-CX3RDK-CU5640

Бренд: e-con Systems Страницы: 9

Бренд: Kanguru Страницы: 13

Бренд: TANDBERG Страницы: 3

Extreme Gaming VGA Cooler GV1000

Бренд: ZALMAN Страницы: 7

Бренд: LevelOne Страницы: 3

Бренд: Kontron Страницы: 62

Wisenet XRN-6410RB2-24TB

Бренд: Hanwha Techwin Страницы: 124

i.LON SmartServer

Бренд: Echelon Страницы: 34

Бренд: Lanpro Страницы: 3

Бренд: Lefroy Brooks Страницы: 10

ExpressCard 11-in-1 Reader/Writer

Бренд: SIIG Страницы: 8

Бренд: Mitsubishi Страницы: 188

Бренд: FDI Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды