National Instruments NI PXIe-8133 Скачать руководство пользователя | Manualshive

Страница: 45 / 92

background image

Chapter 2

Installation and Configuration

NI PXIe-8133 User Manual

2-28

ni.com

ExpressCard

This section provides information on the installation and removal of
ExpressCard

™

modules.

Installing an ExpressCard

You can install an ExpressCard module while the NI PXIe-8133 is running.
The NI PXIe-8133 will automatically detect the card. ExpressCards are
generally marked with a symbol or a label to indicate which end to insert
into the slot. The cards are keyed to prevent incorrect insertion.

To install an ExpressCard, complete the following steps.

1.

Hold the card so the top side is facing left.

2.

Insert the card until it is completely seated in its connector. The
connector has an automatic eject mechanism. If you insert the card
and it is ejected, simply re-insert the card until it is seated.

If you encounter too much resistance, do not force the card. Check the card
orientation and try again.

The NI PXIe-8133 will automatically recognize the ExpressCard and load
the appropriate driver(s). Third-party cards may require that you install
additional drivers. Contact your ExpressCard vendor for more information.

Removing an ExpressCard

To remove the ExpressCard module push in the module and then release to
eject the card. Slide the card out of the slot.

Caution

To avoid data loss and other potential issues, stop communication with your

ExpressCard device before removing it from the NI PXIe-8133. In Windows, use the
Safely Remove Hardware tool to safely stop the ExpressCard.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
43
44
45
46
47
...
»

Содержание NI PXIe-8133





























































































Отзывы:

Нет отзывов

Похожие инструкции для NI PXIe-8133

Бренд: Ubiquiti Страницы: 24

Univerge SV9300

Бренд: NEC Страницы: 26

Бренд: NEC Страницы: 20

DS2000 IntraMail

Бренд: NEC Страницы: 2

UP Squared 6000 Edge Computing Kit

Бренд: Aaeon Страницы: 59

neutrino series

Бренд: Xilica Audio Design Страницы: 26

Бренд: Garland Страницы: 6

Бренд: Hama Страницы: 8

Бренд: FOR-A Страницы: 39

Бренд: addlink Страницы: 9

1394 Dual-Port CardBus

Бренд: SIIG Страницы: 8

Secure Site Manager 16

Бренд: Black Box Страницы: 16

Бренд: Kentrox Страницы: 246

2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011

Бренд: Intel Страницы: 172

IQ Switch ProxSense RS100

Бренд: Azoteq Страницы: 9

Бренд: AG Страницы: 10

Бренд: Datacom Страницы: 45

INTEL CORE i5 SYSTEM BOARD

Бренд: Aprotech Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды