National Instruments NI PXIe-8133 Скачать руководство пользователя

Страница: 38 / 92

Chapter 2

Installation and Configuration

National Instruments

2-21

NI PXIe-8133 User Manual

(Optional) Set the network configuration options of the RT target in the

IP Settings

section and click the

Apply

button.

For information about configuring network settings, refer to the

Configuring Network Settings

book, accessible by browsing to

MAX Remote Systems Help»LabVIEW Real-Time Target
Configuration»Configuring Network Settings

from the

Contents

tab of

MAX Help

Note

When any IP or identification settings are changed, you will be prompted to reboot

the controller for the changes to take effect. Click

Yes

to automatically reboot the RT

target. You may also reboot the controller by right-clicking on the target name under

Remote Systems

and selecting

Reboot

After rebooting the PXI Express controller it will appear in the

Remote Systems

category with the assigned name.

Expand the PXI Express controller view in the

Remote Systems

branch and select

Software

Click the

Add/Remove Software

button in the toolbar to launch the

LabVIEW Real-Time Software Wizard.

Install the LabVIEW Real-Time software and device drivers that you
require on the RT target. Refer to the NI Web site at

ni.com/info

and

enter the Info Code

etspc

for the latest information about supported

software.

After installation of the software the controller will automatically reboot
and you will now be able to program it using LabVIEW Real-Time.

Note

Refer to the

RT Getting Started Guide

available on your host computer for more

information about setting up your RT target.

LabVIEW RT Configuration Switches

Use the LabVIEW RT configuration switches to configure LabVIEW RT
if it is installed on the controller. If you are not using LabVIEW RT, these
switches should remain in the OFF position. The controller reads these
switches only after a system reset.

Note

You must reboot the controller for any changes to take place.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание NI PXIe-8133





























































































Результаты поиска

Содержание NI PXIe-8133

Отзывы:

Похожие инструкции для NI PXIe-8133

Бренды по названию

Популярные бренды

National Instruments NI PXIe-8133, Руководство пользователя

Результаты поиска

Содержание NI PXIe-8133

Отзывы:

Похожие инструкции для NI PXIe-8133

Бренды по названию

Популярные бренды