National Instruments NI PXIe-8133 Скачать руководство пользователя | Manualshive

Страница: 35 / 92

background image

Chapter 2

Installation and Configuration

NI PXIe-8133 User Manual

2-18

ni.com

BIOS Diagnostic Utilities

You can test the hard drive and memory of your controller with the
included BIOS diagnostic utilities.

Accessing BIOS Diagnostic Utilities

Complete the following steps to start the BIOS Diagnostic Utility.

1.

Power on or reboot your controller.

2.

When the message

<F2> to run diagnostics

appears, press the <F2>

key. The first diagnostic utility loads after a short delay.

Hard Drive Diagnostic Utility

The hard drive is tested first upon entry into the BIOS Diagnostic Utilities.
A quick test is performed initially, and a more comprehensive test is
performed second. The user may abort and skip any test by pressing the
<Esc> key at any time during that test. After both tests have finished or
been skipped, the user is presented with the testing results. If both tests have
succeeded or been skipped,

Press any key to continue

is displayed. In

order to continue with testing, user interaction is required to press a key on
the keyboard.

Note

If either hard drive test fails, the controller is not permitted to boot, and the user is

instructed to turn off the controller and replace the hard drive.

Memory Diagnostic Utility

The memory diagnostic utility is started immediately after the user presses
a key to exit the hard drive diagnostic utility. The user may abort and skip
the memory test by pressing the <Esc> key at any time during this test.
After the memory utility has finished or been skipped, the user is presented
with the testing result. If the memory test was successful or skipped,

Press

any key to continue

is displayed. In order to continue to boot the

controller, user interaction is required to press a key on the keyboard.

Note

If the memory test fails, the controller is not permitted to boot, and the user is

instructed to turn off the controller and replace the memory.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
33
34
35
36
37
...
»

Содержание NI PXIe-8133





























































































Отзывы:

Нет отзывов

Похожие инструкции для NI PXIe-8133

Бренд: Paradyne Страницы: 16

Бренд: Barco Страницы: 100

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 19

Бренд: National Instruments Страницы: 103

NI PXI-1042 Series

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 4

Бренд: X-Micro Страницы: 9

Бренд: X-Micro Страницы: 19

Бренд: Baldor Страницы: 34

Бренд: H3C Страницы: 3

Бренд: red lion Страницы: 5

PCIe/PXIe-6301 Series

Бренд: JYTEK Страницы: 46

Бренд: Datum Страницы: 49

Бренд: Navitar Страницы: 1

Бренд: SilverStone Страницы: 12

VXC-114U Series

Бренд: ICP DAS USA Страницы: 8

EK-UNI Holder D5 V3

Бренд: ekwb Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды