National Instruments cDAQ-9133 Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 145

background image

© National Instruments

|

A-9

NI cDAQ-9132/9133/9134/9135/9136/9137 User Manual

Save & Exit Menu

The Save & Exit setup menu includes all available options for exiting, saving, and loading the
BIOS default configuration. As an alternative to this screen, press <F9> to load optimal BIOS
default settings and <F10> to save changes and exit setup.

The Exit setup menu includes the following settings:
•

Save Changes and Reset

—Any changes made to BIOS settings are stored in NVRAM.

The setup utility then exits and reboots the controller. The <F10> key can also be used to
select this option.

•

Discard Changes and Reset

—Any changes made to BIOS settings during this session of

the BIOS setup utility are discarded. The setup utility then exits and reboots the controller.
The <Esc> key can also be used to select this option.

•

Save Changes

—Changes made to BIOS settings during this session are committed to

NVRAM. The setup utility remains active, allowing further changes.

•

Discard Changes

—Any changes made to BIOS settings during this session of the BIOS

setup utility are discarded. The BIOS setup continues to be active.

•

Restore Factory Defaults

—This option restores all BIOS settings to the factory default.

This option is useful if the controller exhibits unpredictable behavior due to an incorrect or
inappropriate BIOS setting. Notice that any nondefault settings such as boot order,
passwords, and so on, are also restored to their factory defaults. The <F9> key can also be
used to select this option.

•

Save As User Defaults

—This option saves a copy of the current BIOS settings as the User

Defaults. This option is useful for preserving custom BIOS setup configurations.

•

Restore User Defaults

—This option restores all BIOS settings to the user defaults. This

option is useful for restoring previously preserved custom BIOS setup configurations.

•

Boot Override

—This option lists all possible bootable devices and allows the user to

override the Boot Option Priorities list for the current boot. If no changes have been made
to the BIOS setup options, the system will continue booting to the selected device without
first rebooting. If BIOS setup options have been changed and saved, a reboot will be
required and the boot override selection will not be valid.

Resetting the BIOS Settings

Refer to the

Resetting the System CMOS and BIOS Settings

section of Chapter 1,

Getting Started

with the cDAQ Controller

, for steps to take to reset the CMOS and BIOS settings to factory

default values.

«
...
132
133
134
135
136
...
»

Содержание cDAQ-9133


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для cDAQ-9133

ServeRAID M5014

Бренд: IBM Страницы: 106

Бренд: ZIMO Страницы: 38

Бренд: Campbell Страницы: 34

Бренд: Dahua Страницы: 58

Flashlight Blue

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 4

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 5

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 6

Бренд: Saab Страницы: 4

Бренд: ZKTeco Страницы: 14

Бренд: Ziton Страницы: 28

Бренд: Unico Страницы: 164

Бренд: DANIEL Страницы: 48

Бренд: Bardiani Страницы: 96

Бренд: Eaton Страницы: 4

Бренд: Parker Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды