National Instruments cDAQ-9133 Скачать руководство пользователя страница 34

Страница: 34 / 145

1-24

ni.com

Chapter 1

Getting Started with the cDAQ Controller

Using the cDAQ Controller on a Desktop

You can install the NI desktop mount kit to the cDAQ controller. Complete the following steps
to install the NI desktop mount kit, part number 779473-01, on the cDAQ controller.
1.

Align one of the end brackets with the mounting hole at one of the ends of the controller,
as shown in Figure 1-16.

Figure 1-16.

Connecting the End Brackets to the Controller (cDAQ-9134 Shown)

Use a number 2 Phillips screwdriver to tighten the captive screw on the end bracket.

Repeat steps 1 and 2 to attach the other end bracket to the other end of the controller.

Note

To achieve the highest accuracy when mounting the controller in the desktop

kit, NI recommends that you operate the controller with the modules rotated forward,
as shown in Figures 1-17 and 1-18. Visit

ni.com/info

and enter the Info Code

cdaqmounting

for more information about mounting and accuracy.

Mounting Holes

Captive Screw

NI cD

-913

-9

NI CompactD

Содержание cDAQ-9133


















































































































































Результаты поиска

Содержание cDAQ-9133

Отзывы:

National Instruments cDAQ-9133, Руководство пользователя, Страница: 34 / 145

Результаты поиска

Содержание cDAQ-9133

Отзывы: