NACD SP318AM Series страница 53 Скачать руководство пользователя

Страница: 53 / 88

North American Clutch & Driveline

Rockford, Illinois

Phone: (800) 383-9204

(815) 282-7960

Fax (815) 282-9160

www.naclutch.com

Remove the clutch and puller from the clutch shaft. Remove the hub key if it was not removed

with the clutch.

CLUTCH DISASSEMBLY

All 18 inch model clutches

1. Set the clutch assembly on a bench with the throwout collar facing up. Disengage the clutch.

2. Remove the grease fitting (23) from the hose fitting (20). Remove the hose (19) and hose

fitting (18) from the trunnion of the collar assembly.

3. Remove the four cotter pins (17) from the four clevis pins (16) securing the sliding sleeve to

the links (15).

4. Remove the sleeve and collar assembly from the links.

BRONZE COLLAR DISASSEMBLY

5. Remove two hex huts and two hex head bolts to remove the throwout collar halves and

shims from the sliding sleeve.

BALL BEARING COLLAR DISASSEMBLY

6. If the unit has a grease shield (73), use a large flat screwdriver to pry it from the collar (28).

7. Remove the internal snap ring (31) from the collar.

8. Remove the external snap ring (29) from the sliding sleeve (27).

9. Press the sleeve from the bearing and collar in a press or pull the bearing from the sleeve.

10. Remove the snap ring (29) from the sleeve.

Содержание SP318AM Series

























































































Результаты поиска

Содержание SP318AM Series

Отзывы:

Похожие инструкции для SP318AM Series

Бренды по названию

Популярные бренды

NACD SP318AM Series, Руководство по обслуживанию

Результаты поиска

Содержание SP318AM Series

Отзывы:

Похожие инструкции для SP318AM Series

Бренды по названию

Популярные бренды