NACD SP318AM Series Скачать руководство пользователя страница 69

Страница: 69 / 88

North American Clutch & Driveline

Rockford, Illinois

Phone: (800) 383-9204

(815) 282-7960

Fax (815) 282-9160

www.naclutch.com

Bearing Carrier

3. Set the bearing carrier (47) on the bed of a press with the output of the housing facing up.

4. Coat the bearings with a light film of clean No.30 engine oil.

5. Hand pack the bearings with grease as described in the Description and Specifications section.

Assembly

Install the Clutch shaft and bearing into the bearing carrier.

6. Place the bearing carrier (47) in a large bench vise with protective jaws or secure support

it on a bench with the input end up. There must be sufficient clearance below the carrier to

install the shaft.

7. Install the shaft with bearings in the bearing carrier. The lower bearing must seat securely in

the bottom of the bore.

8. Install bearing retainer (38) in the bearing carrier (47) resting securely against the front

bearing (40).

9. Install six hex head capscrews (35) with washers (36). Torque the capscrews to the proper

specifications given in Torque Values for Fasteners in the Description and Specifications

section.

Install the bearing carrier unit on the clutch housing.

10. Set the clutch housing (44) on a work bench, securely supported with wooden blocks,

with the input end of the housing facing down. There should be sufficient clearance below the

housing to allow for installation of the clutch shaft.

11. Lift the bearing carrier and shaft a hoist securely attached to it. Carefully lower the bearing

carrier and shaft onto the clutch housing. Disconnect the hoist. Position the carrier so the

fitting (51) will be up when the clutch housing is in its final position on the engine.

Содержание SP318AM Series

























































































Результаты поиска

Содержание SP318AM Series

Отзывы:

NACD SP318AM Series, Руководство по обслуживанию, Страница: 69 / 88

Результаты поиска

Содержание SP318AM Series

Отзывы: