NACD SP318AM Series страница 55 Скачать руководство пользователя

Страница: 55 / 88

North American Clutch & Driveline

Rockford, Illinois

Phone: (800) 383-9204

(815) 282-7960

Fax (815) 282-9160

www.naclutch.com

CLUTCH SHAFT AND HOUSING DISASSEMBLY – CONFIGURATION C

Figure 27. Illustration – Configuration C

1. Turn the power take-off housing with attached parts over on the bench. Support the housing

so the output end of the clutch shaft faces up and is free to rotate. There should be a clearance

below the input end of the clutch shaft.

2. Remove hex head capscrews (48) and washers (49) and remove the support plate if used.

3. Lift the clutch shaft (33) and bearing carrier (47) unit from the clutch housing (44).

4. Secure the bearing carrier with attached parts in a large vise with protective jaws, with the

input end of the shaft facing up, gripping the rear cast section of the bearing carrier in the vise.

5. Remove the six hex head capscrews (35) and washers (36) that secure the bearing retainer

(38) to the bearing carrier.

Содержание SP318AM Series

























































































Результаты поиска

Содержание SP318AM Series

Отзывы:

Похожие инструкции для SP318AM Series

Бренды по названию

Популярные бренды

NACD SP318AM Series, Руководство по обслуживанию

Результаты поиска

Содержание SP318AM Series

Отзывы:

Похожие инструкции для SP318AM Series

Бренды по названию

Популярные бренды