NACD SP318AM Series страница 30 Скачать руководство пользователя

Страница: 30 / 88

North American Clutch & Driveline

Rockford, Illinois

Phone: (800) 383-9204

(815) 282-7960

Fax (815) 282-9160

www.naclutch.com

Install the support plate. Refer to support plate information in NACD PTO Support Plate

Specifications in the Description and Specifications section, install six ½ x 13UNC –

2A. Torque to 108 Nm. (80 lb. –ft).

Note: Verify proper shimming and alignment of the support plate.

Tighten the belts to the manufacturer’s specifications, being sure that belt tension

does not cause excessive deflection. (Refer to information in the Description and

Specifications section and Installation Tips in this section to measure and assure that

excessive deflection does not occur when the belt are tightened).

Install the hand lever assembly (53) and torque the hex head capscrew to the proper

specifications given in Torque Values for Fasteners in the Description and Specification

section of this manual.

19.

20.

21.

HAND LEVER POSITION FOR NACD POWER TAKE-OFFS

Normal Position: Operating Shaft Horizontal

To insure there is no preload on the shifting mechanism, the hand lever position with the clutch

engaged should be slightly past vertical position, slightly towards engine.

The handle should NEVER be installed in a horizontal position when the operating shaft is

positioned horizontally. Improper handle position can cause throwout.

Figure 16. Hand Lever Position

Содержание SP318AM Series

























































































Результаты поиска

Содержание SP318AM Series

Отзывы:

Похожие инструкции для SP318AM Series

Бренды по названию

Популярные бренды

NACD SP318AM Series, Руководство по обслуживанию

Результаты поиска

Содержание SP318AM Series

Отзывы:

Похожие инструкции для SP318AM Series

Бренды по названию

Популярные бренды