NACD SP318AM Series страница 57 Скачать руководство пользователя

Страница: 57 / 88

North American Clutch & Driveline

Rockford, Illinois

Phone: (800) 383-9204

(815) 282-7960

Fax (815) 282-9160

www.naclutch.com

4. Remove the hex head capscrews (65) and remove the rear bearing retainer (64) from the

sheave housing if not previously removed.

5. Remove the hex head capscrews (48) that secure the sheave housing (60) to the clutch

housing (44) and remove the sheave housing if not previously removed.

Note: The inner race of bearing (41) will remain on the shaft.

1. Remove the sheave from the shaft.

2. Remove the outer race of bearing (41) from the sheave housing if not previously removed.

3. Remove the fitting (50) from the bearing retainer.

4. Remove the twelve hex head capscrews (35) and remove the front bearings (38) from the

clutch housing (44).

5. Lift clutch shaft (33) with the inner races of the front and rear bearings (40&41) from the

clutch housing.

6. Remove the outer race of the rear bearing (40) from the main housing.

7. Using a split-type bearing puller, remove the inner race of the rear bearing (41) from the shaft.

8. Using a split-type bearing puller, remove the inner race of the front bearing (40) from the shaft.

Содержание SP318AM Series

























































































Результаты поиска

Содержание SP318AM Series

Отзывы:

Похожие инструкции для SP318AM Series

Бренды по названию

Популярные бренды

NACD SP318AM Series, Руководство по обслуживанию

Результаты поиска

Содержание SP318AM Series

Отзывы:

Похожие инструкции для SP318AM Series

Бренды по названию

Популярные бренды