Muratec F-525 Скачать руководство пользователя страница 167

Страница: 167 / 383

3-83

Unique Switch 015 — Transmission

Switch

Initial

Setting

Adjust

Usage/Comments

Factory use only

Not used

Factory use only

V.8 handshake in manual Tx

0: No

1: Yes

Determine I the handshaking will be done with V.8

recommendation if manual transmission.

Unique Switch 016 — Transmission

Switch

Initial

Setting

Adjust

Usage/Comments

Available *, # and space

upon

F-code

box registration

0: No

1: Yes

Determines if the * (asterisk), # (sharp) and space

are available upon

F-code

box registration.

Available *, # and space

upon

F-code

communicating

0: No

1: Yes

Determines if the * (asterisk), # (sharp) and space

are available upon

F-code

communicating.

Ignore space in

F-code

0: Yes

1: No

Determines if checking the space stored in the

F-code

ID.

F-code sub-frame off

0: Send

1: Not send

Do not send the sub-address and password of

F-code box when a point of sending DCS signal

after EOM signal.

Send F-code box’s TTI

0: No

1: Yes

Transmit the sub-address and box name of F-code

box with F-code polling document.

Factory use only

Retrieve document

0: No

1: Yes

Retrieve the document received in F-code

SecureMail box by polling transmission.

Ignore F-code bit

0: No

1: Yes

Neglect SEP bit of DTC signal or SUB bit of DCS

signal at F-code polled transmission.

Note:

The “F-code communication” is possible the SecureMail and Polling operation using the F-code

(SUB/SEP/PWD/SID). However, it is not based on T.33 recommendation.

Содержание F-525
































































































































































































































































































































































































Результаты поиска

Содержание F-525

Отзывы:

Muratec F-525, Руководство по полевой инженерии, Страница: 167 / 383

Результаты поиска

Содержание F-525

Отзывы: