Muratec F-525 Скачать руководство пользователя страница 107

Страница: 107 / 383

3-23

Machine Parameter 182 ~ 186 — Factory use only

Machine Parameter 187

Switch

Initial

Setting

Adjust

Usage/Comments

Printer registration

adjustment (Vertical) at the

Bypass tray for printing.

Adjusts the start point to

print.

The plus setting increases

the top margin and the minus

setting decreases it.

Each setting changes by

0.1 mm.

Switch

76543210 Settings

127 steps 01111111

+12.7 mm

32 steps

00100000

+3.2 mm

16 steps

00010000

+1.6 mm

8 steps

00001000

+0.8 mm

00000000

0 mm



Initial setting

Note:

Set this switch after setting the margin to

“0 mm” in Unique Switch 052. Then, after setting

this switch, set the margin to the initial setting (4

mm) in Unique Switch 52.

Machine Parameter 188

Switch

Initial

Setting

Adjust

Usage/Comments

Printer registration

adjustment (Vertical) for

duplex printing cassette.

Adjusts the start point to

print.

The plus setting increases

the top margin and the minus

setting decreases it.

Each setting changes by

0.1 mm.

Switch

76543210 Settings

127 steps 01111111

+12.7 mm

32 steps

00100000

+3.2 mm

16 steps

00010000

+1.6 mm

8 steps

00001000

+0.8 mm

00000000

0 mm



Initial setting

Note:

Set this switch after setting the margin to

“0 mm” in Unique Switch 052. Then, after setting

this switch, set the margin to the initial setting (4

mm) in Unique Switch 52.

Machine Parameter 189 ~ 219 — Factory use only

Содержание F-525
































































































































































































































































































































































































Результаты поиска

Содержание F-525

Отзывы:

Muratec F-525, Руководство по полевой инженерии, Страница: 107 / 383

Результаты поиска

Содержание F-525

Отзывы: