MTD 25cc Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 64

background image

Maintenance

9

Storage

When storing a piece of gas powered equipment for longer than 4 weeks, the following procedures will prolong

the engine life and minimize issues such as hard starting after storage.

1.

Run the engine until it is out of gas.

2.

Open the air filter cover.

3.

Spray some oil down the throat of the carburetor.

4.

Close the air filter cover.

5.

Pull the starter rope to turn the engine over a few times.

Returning to service:

•

When returning to service, fill the fuel tank with fresh fuel/oil mix.

•

The engine should start normally.

For Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

«
...
11
12
13
14
15
...
»

Содержание 25cc

































































Отзывы:

Нет отзывов

Похожие инструкции для 25cc

Бренд: Rail King Страницы: 46

3T-MOTORS 3T45-20

Бренд: 3T-Components Страницы: 24

Бренд: brel-motors Страницы: 2

OMEGAFLEX FPU5-MT-110

Бренд: Omega Engineering Страницы: 83

ERS VAR10 SZ 2500

Бренд: Warner Страницы: 16

Бренд: KONTRONIK Страницы: 11

Бренд: Rotax Страницы: 84

Бренд: Rotax Страницы: 166

Бренд: Oriental motor Страницы: 8

Бренд: Oriental motor Страницы: 12

Бренд: SSANGYONG Страницы: 14

Бренд: MerCruiser Страницы: 118

Sterndrive 4.3L TKS

Бренд: MerCruiser Страницы: 130

Бренд: MerCruiser Страницы: 135

Бренд: DJ ENGINE Страницы: 9

Бренд: Texas Equipment Страницы: 44

Бренд: Yanmar Страницы: 84

Бренд: DANA Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды