MTD 25cc Скачать руководство пользователя страница 53

Страница: 53 / 64

Clutch and Upper Drive Shaft

Clutch removal/replacement

NOTE:

The upper drive shaft may be left connected to the

clutch housing. Removing the three screws in the
clutch housing will allow the clutch housing and the
upper drive shaft to be removed as one.

1. Remove the three screws holding the clutch housing

on with a T-20 driver. See Figure 7.5.

Disconnect and remove the spark plug.

Insert at least 18” (0.5 M) of starter rope in the spark
plug hole to keep the crank shaft from rotating. Keep
some of the rope out so it can be removed later.
See Figure 7.6.

Remove the clutch drum by removing the screw in
the center of it with a T-20 driver. See Figure 7.7.

Clutch housing

Figure 7.5

screws

Clutch housing screws

Figure 7.6

Insert at least 18” of rope

in the hole

Figure 7.7

Clutch drum

For Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание 25cc

































































Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды

MTD 25cc, Профессиональное руководство по эксплуатации

Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды