MTD 25cc Скачать руководство пользователя страница 60

Страница: 60 / 64

P25 Series of Engines

NOTE:

Apply a coating of Slick 50

or similar prod-

uct to the connecting rod bearing as a
assembly lube.

Place the cylinder O-ring on the crankcase.

Slide the connecting rod onto the crankshaft pin.

NOTE:

The lettering on the connecting rod bearing

must face the crankshaft and the exhaust
port must face the mounting arm of the igni-
tion coil. See Figure 8.13.

Apply a thread locking compound such as Loctite
266 to the cylinder bolts. Install the cylinder bolts
using a T-30 torx driver and tighten them to a torque
of 110 - 120 in lbs (12 - 14 Nm). See Figure 8.14.

Apply a light coat of oil to the O-ring on the engine
cover. See Figure 8.15.

Install the engine cover and tighten the two screws
to a torque of 30 - 40 in lbs (3 - 5 Nm).

Figure 8.13

Exhaust port

Mounting arm of

the ignition coil

Lettering facing in

Figure 8.14

Cylinder bolts

Figure 8.15

O-ring

For Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание 25cc

































































Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды

MTD 25cc, Профессиональное руководство по эксплуатации

Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды