MTD 25cc Скачать руководство пользователя страница 57

Страница: 57 / 64

Engine Assembly

Rotate the flywheel so that the magnets are away
from the module.

Remove the two screws that secure the ignition mod-
ule to the block using a T-20 torx driver.
See Figure 8.4.

Remove the module.

Remove the flywheel by applying a sharp blow to the
crankshaft while gently prying upward with a pry bar.
The flywheel will loosen then lift it off. See Figure 8.5.

NOTE:

If replacing a short block, exchange the crankcase

and cylinder with the short block and follow the
previous steps in reverse order.

Remove the muffler using a T-27 torx driver or a 5/
16” wrench. See Figure 8.6.

Figure 8.4

Screws

Figure 8.5

Never hit the

crank shaft with

a hammer!

use a brass punch

! CAUTION

Never strike the crankshaft
directly with a hammer. To pre-
vent damage to the crankshaft

use a brass punch or a piece of wood
between the hammer and the crankshaft.

Figure 8.6

Muffler screws

For Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание 25cc

































































Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды

MTD 25cc, Профессиональное руководство по эксплуатации

Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды