MTD 25cc Скачать руководство пользователя страница 8

Страница: 8 / 64

P25 Series of engines

Model and Serial Numbers

The model (item) and serial number are on a little

white sticker with bar code. These are the numbers
needed when ordering parts. This sticker can be found on
the side of the engine.

The model number is 41BD160G965. The break down of what the number mean is as follows:

41 ............................................................................................ Hand held product

........B. ..................................................................................... Sales level

........... D.................................................................................. Product type

.................160 ......................................................................... Unique Identifier

.........................G..................................................................... Packaging code

.............................965 ............................................................. Customer number

The serial number is 1H130DI1521. The serial number reads as follows:

1 .............................................................................................. Engineering level

...H........................................................................................... Month of production (H = August)

.....13 ....................................................................................... Day of the month

.........0 ..................................................................................... Last digit of the year

...........D................................................................................... Plant it was built in (MTD Southwest)

..............I ................................................................................. Assembly line number

.................1521 ....................................................................... Number of unit built

Figure 1.4

Model number

Serial number

For Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание 25cc

































































Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды

MTD 25cc, Профессиональное руководство по эксплуатации

Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды