MTD 25cc Скачать руководство пользователя страница 29

Страница: 29 / 64

Fuel System And Carburetor

The function of the fuel system is to store fuel/oil mixture, mix the fuel/oil with air and deliver it to the combustion

chamber. The fuel system consists of the following components:

•

Fuel tank

•

Fuel lines

•

Fuel filter

•

Carburetor

NOTE:

When working on the fuel systems, look at the whole system. A problem will rarely be isolated to one

component.

Fuel system troubleshooting

When troubleshooting the fuel system, all of these steps should be followed:

NOTE:

A compression test must be preformed before troubleshooting the fuel system. The fuel system will not

work properly with a compression reading less than 90 psi (6.2 bar).

Drain the fuel.

Inspect the fuel.

Check the fuel/oil mixture.

Test for alcohol.

Inspect the fuel filter.

Inspect the fuel lines.

Check the fuel tank vent.

Inspect the primer.

Inspecting the fuel

NOTE:

Fuel is the maintenance item most often overlooked by consumers. A lot of fuel system problems are

caused by bad gasoline. When inspecting the fuel:

•

Look for water.

•

Look for dirt.

•

Look for discoloration.

•

Sniff carefully to see if it smells like varnish or kerosene.

•

Save the fuel to show to customer.

NOTE:

Save a sample of the fuel collected to show the customer.

! W A R N IN G

Gasoline is extremely flammable and the vapors are explosive. Avoid all sources of heat when
working on the fuel system.

CHAPTER 5: FUEL SYSTEM AND CARBURETOR

For Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание 25cc

































































Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды

MTD 25cc, Профессиональное руководство по эксплуатации

Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды