MTD 25cc Скачать руководство пользователя страница 61

Страница: 61 / 64

Engine Assembly

10.

Install the flywheel and module by following the procedures described in Chapter 4: Ignition.

11.

Install the muffler.

NOTE:

Apply a thread locking compound such as Loctite 266 to the muffler screws. Tighten the screws to a

torque of 80 - 90 in. lbs (9 - 10 Nm).

12.

Install the starter by following the procedures described in Chapter 6:Starter.

13.

Install the carburetor spacer, the carburetor and the fuel tank by following the procedures described in Chapter
5: Fuel System and Carburetor.

14.

Install the clutch, clutch housing and drive shaft assembly by following the procedures described in Chapter 7:
Clutch and Drive Shaft.

15.

Install the spark plug.

16.

Test run the engine before returning it to service.

* Apply a small amount of releasable thread locking compound such as Loctite® 242 (blue).

Torque Values

Torque Value

in lbs

Cylinder screws*

110 -120

12 - 14

Spark plug

160 - 220

18 - 25

Muffler screws*

80 - 90

9 - 10

Module screws

30 - 40

3 - 5

Clutch drum

38 - 40

4 - 5

Clutch rotor

210 - 230

24 - 26

Clutch housing screws

25 - 30

Carburetor screws

35 - 40

4 - 5

Insulator block screws*

45 - 50

5 - 6

Starter housing screws

30 - 40

3 - 5

Starter pressure plate

25 - 35

3 - 4

Fuel tank screws

17 - 23

2 - 3

Engine cover screws

30 - 40

3 - 5

For Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание 25cc

































































Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды

MTD 25cc, Профессиональное руководство по эксплуатации

Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды