MTD 25cc Скачать руководство пользователя страница 51

Страница: 51 / 64

Clutch and Upper Drive Shaft

Drive shaft assembly

There are two types of drive shaft assemblies available with the P25 series of engines:

•

Straight shaft

•

Curve shaft

NOTE:

The procedure to remove the drive shaft assembly from the engine is the same for both styles.

NOTE:

The drive shaft assembly consists of the drive shaft housing and a flexible inner drive shaft. The hous-

ing and the drive shaft are serviced separately.

To remove the drive shaft assembly:

1. Remove the six screws in the grip with a T-20 torx

driver. See Figure 7.1.

Let the grip hang off to the side.

NOTE:

There are a five parts inside the grip assembly. Be

careful that they don’t fall out of the grip.
See Figure 7.2.

Figure 7.1

Screws for the grip

Figure 7.2

Trigger

Trigger
spring

Cable

Switch

Wires

(under the cable)

CHAPTER 7: CLUTCH AND UPPER DRIVE SHAFT

For Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание 25cc

































































Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды

MTD 25cc, Профессиональное руководство по эксплуатации

Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды