MTD 25cc Скачать руководство пользователя страница 56

Страница: 56 / 64

P25 Series of Engines

Engine disassembly

Economics and parts availability will determine how much engine disassembly is feasible. There are two main

levels of engine disassembly.

Short block installation.

Short block installation consists of removing the engine, transferring the external parts to the replacement
short block, and installing the engine. External parts consist of:

• Starter

• Ignition system

• Fuel system

• Muffler

Complete tear down

A complete tear down may be done to re-seal the crankcase or for failure analysis.

NOTE:

The only internal engine part available for service is the O-ring between the cylinder and the crank-

case.

NOTE:

The repair/replace choice in warrantable situations must be made using the 2/3 replacement cost rule.

Outside of warranty, the decision is left to the dealer and the customer.

NOTE:

There are a few different paths that can be followed when disassembling an engine. This chapter will

cover the removal of components in one order, but it is written so that the technician can go to the com-
ponent being removed.

Remove the Clutch by following the procedures
described in Chapter 7: Clutch and Drive Shaft.

Remove the starter following the steps described in
Chapter 6: Starter.

Remove the carburetor, insulator block and the fuel
tank by following the procedures described in Chap-
ter 5: Fuel System and Carburetor.

Remove the two screws that hold the engine cover
to the engine using a T-25 torx driver.
See Figure 8.3.

Figure 8.3

Screws

For Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Содержание 25cc

































































Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды

MTD 25cc, Профессиональное руководство по эксплуатации

Результаты поиска

Содержание 25cc

Отзывы:

Похожие инструкции для 25cc

Бренды по названию

Популярные бренды