Motorola APX 4000 Скачать руководство пользователя | Manualshive

Страница: 98 / 526

background image

8-4

Disassembly/Reassembly Procedures

: Radio Disassembly

8.4

Radio Disassembly

This section contains instructions for disassembling the radio's main subassemblies.

Prepare the radio for disassembly:

• Turn off the radio by pressing on the MFK (22) and hold the MFK (Multi Function Knob) until the

radio display shows “Power off?”. Press the Menu Select button below and select Yes to power
off.

• Remove the antenna, the battery, the Accessory-Connector cover (14), the Bottom Label (17)

and any other accessory connected to the radio.

8.4.1

Remove Battery (48)

NOTE:

The Motorola-approved battery shipped with the APX 2000/ APX 4000/ APX 4000Li radio is
uncharged. Prior to using a new battery, charge it per the recommended procedure for the
battery.

1. With the radio turned off, lift up the latch located at the bottom of the battery.

Figure 8-2. Lifting up the latch

To avoid a possible explosion:
• DO NOT charge, remove, or attach the battery in an area

labeled “hazardous atmosphere.”

• DO NOT discard batteries in a fire.

If the radio is programmed for volatile-key retention,
encryption keys will be retained for approximately 30 seconds
after battery removal.

!

C a u t i o n

Battery Latch

«
...
96
97
98
99
100
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Бренд: Daewoo Страницы: 49

Бренд: i-box Страницы: 18

Бренд: Titan Страницы: 11

Бренд: Vertex Standard Страницы: 31

Бренд: Westinghouse Страницы: 100

MICRO WATERPROOF

Бренд: Zodiac Страницы: 37

Бренд: LENCO Страницы: 52

Бренд: Fresh 'N Rebel Страницы: 34

Бренд: Parkside Страницы: 210

Бренд: TechniSat Страницы: 112

Бренд: Mustek Страницы: 1

HDG2000B Series

Бренд: Hantek Страницы: 100

Бренд: Bluetti Страницы: 56

Бренд: Sole Diesel Страницы: 104

Бренд: Makita Страницы: 91

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 100

Бренд: Makita Страницы: 129

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды