Motorola APX 4000 Скачать руководство пользователя страница 473 | Manualshive

Страница: 473 / 526

background image

Disassembly/Reassembly Procedures

: Ensuring Radio Submergibility

8-39

8.7.6

Reassembly

To reassemble the radio:

1. Inspect the Main O-Ringon the Chassis (54) for any damage or foreign material.
2. Inspect the Battery Contact Seal (55) on the Main Board Assembly (45) for any damage.
3. Inspect the mating seal surfaces on the Chassis (54) for all of the above seals for damage or

foreign material that might prevent the seals from sealing properly.

Continue reassembling the radio according to

Tighten all hardware that was loosened or

removed.

8.7.7

Vacuum Test

The Vacuum Test uses a Vacuum Pump to create a negative pressure condition inside the radio. The
gauge measures this pressure and is used to Monitor any pressure changes in the radio. A properly
sealed, watertight radio should have minimal change in pressure during the test.

Before starting the vacuum test:

• Remove the battery and antenna.
• Remove the Vacuum Port Seal (56) and Ventilation Label (57) that cover the Vacuum port.

NOTE:

Refer to the exploded view diagrams and parts lists found in

“Chapter 10: Exploded Views

and Parts Lists”

8.7.7.1 Vacuum Tool Setup

1. Attach one end of the hose to the Vacuum Pump. Attach the other side of the hose to the

Vacuum Test Fixture (P/N: TL000059A01).

2. Tool Leak Test:

i.

Block the open end of the Vacuum Test Fixture.

ii.

Pull the knob on the Vacuum Pump to create vacuum.

iii.

Pump at least 15 in Hg.

iv.

Watch the gauge for a minute. If there is any loss of vacuum, repair or replace the tool.

3. Ensure that the seal is attached to the Vacuum Test Fixture.

NOTE:

The actual reading of the gauge at this point is not important; it is important that the gauge
pointer remained steady, indicating that there are no vacuum leaks in the pump.

Do not reassemble the radio without first performing the
following preliminary inspection procedure.

!

C a u t i o n

«
...
471
472
473
474
475
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Architectual AQ215

Бренд: Martin Audio Страницы: 1

Бренд: GOWIN Страницы: 2

Бренд: Durapac Страницы: 12

Бренд: Lasonic Страницы: 28

Бренд: Sirius XM RAdio Страницы: 26

Бренд: Westerbeke Страницы: 95

Бренд: Caltta Страницы: 10

Бренд: Noxon Страницы: 20

Бренд: Parkside Страницы: 210

EDDINGTON EDD-DAB-BLK

Бренд: MAJORITY Страницы: 26

Бренд: Briggs & Stratton Страницы: 12

DPC-7400 Series

Бренд: Daewoo Страницы: 26

Бренд: Cobra Страницы: 38

Бренд: Cirro Страницы: 8

Бренд: Coby Страницы: 1

Бренд: GME Страницы: 33

Бренд: Retekess Страницы: 2

Бренд: Hannlomax Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды