Motorola APX 4000 Скачать руководство пользователя страница 221

Страница: 221 / 526

Disassembly/Reassembly Procedures

: Radio Disassembly

7-13

Figure 7-18. Remove the Keypad Board

7.4.5.7 Removal of the Keypad (8)

1. With the Keypad Board (10) removed, gently press the Keypad (8) from the front of the Front

Housing (2) with fingers or with the aid of the back of the black stick to disengage the Keypad
from the rib as shown in

Figure 7-19.

Figure 7-19. Disengage the Keypad

2. With the Keypad (8) disengaged from the rib, gently lift it out from the Front Housing (2).

When disengaging and removing the Keypad, care is needed
to avoid tearing and damange to the Keypad.

C a u t i o n

Black Stick’s Back

Содержание APX 4000















































































































































































































































































































































































































































































































































Результаты поиска

Содержание APX 4000

Отзывы:

Похожие инструкции для APX 4000

Бренды по названию

Популярные бренды

Motorola APX 4000, Базовое руководство по обслуживанию

Результаты поиска

Содержание APX 4000

Отзывы:

Похожие инструкции для APX 4000

Бренды по названию

Популярные бренды