Motorola APX 4000 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 526

Motorola APX 4000 Скачать руководство пользователя страница 52

5-4

Performance Checks

: Display Radio Test Mode

NOTE:

All displays are temporary and will expire without any user intervention. If information is

longer than the physical length of the radio’s display, the information will wrap around to
the next display. After the last display, “

RF TEST

” is displayed.

To freeze any of the displays, press the left arrow on the 4-Way Navigation Button. To
resume automatic scrolling, press the right arrow on the 4-Way Navigation Button. To
rapidly scroll forward through the displays, continue pressing the right arrow. You cannot
scroll backwards.

NOTE:

Press the

Top Side Button

(Purple button) to advance the test environments from “

RF

TEST

”, “

CH TEST

”, “

RGB TEST

” then press the

Top Button

(Orange button) to confirm selection. Press any other buttons to advance the

test.

Once a test is carried out, restart the radio to proceed to another test.

3. Do one of the following:

• Press the

Top

Side Button

to stop the displays and toggle between RF test mode and the

Control Top and Keypad test mode. The test mode menu “

CH TEST

” is displayed,

indicating that you have selected the Control Top and Keypad test mode. Go to Section

“5.2.3 Control Top and Keypad Test Mode” on page 1:5-7

NOTE:

Each press of the

Top

Side Button

(Purple button) scrolls through “

RF TEST

”,

“

CH TEST

” and “

RGB TEST

”.

• Press the

Top Button

(Orange button) to stop the displays and put the radio into the RF

test mode. The test mode menu, “

1 CSQ

”, is displayed, indicating test frequency 1, Carrier

SQuelch mode. Go to Section

“5.2.2 RF Test Mode” below

.

NOTE:

Once your radio is in a particular test mode, you must turn off the radio and turn it
back on again to access the other test mode.

FLASHcode

The FLASH codes as programmed in the
codeplug

Always

RF band 1

The radio’s operating frequency

Always

Tuning Ver

Version of Tuning codeplug

Always

Proc Ver

Version of Processor

Always

Option Board
Type

Type of Keypad board being used

When the radio has an Option
Board/Expanded Keypad Board.

Option Board
Serial Number

Serial number of the Keypad board is
displayed

When the radio has an
Expanded Keypad Board.

Option Board
Bluetooth Addr

Bluetooth Address of the Keypad board is
displayed

When the radio has an
Expanded Keypad Board.

Option Board
Sw Version

Software version of the Keypad Board is
displayed

When the radio has an
Expanded Keypad Board.

Exp Board Type

Type of Keypad Board is displayed

When the radio has a Keypad
Board.

Table 5-2. Test-Mode Displays (Continued)

Name of Display

Description

Appears

«
...
50
51
52
53
54
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов