Motorola APX 4000 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 526

background image

6-18

Radio Alignment Procedures

: Transmitter Alignments

6.5.5

Transmit Deviation Balance Alignment

This alignment procedure balances the modulation contributions of the low- and high-frequency
portions of a baseband signal. Proper alignment is critical to the operation of signalling schemes that
have very low frequency components (for example, DPL) and could result in distorted waveforms if
improperly adjusted.

This procedure needs to be performed at multiple frequencies to allow for proper alignment across
the entire RF band. The RF band is divided into frequency zones with a calibration point (value) in
each zone.

NOTE:

This alignment is required after replacing (or servicing) the main board.

Proper alignment requires a modulation analyzer or meter with a frequency response to less than
10 Hz modulating frequency. The modulation analyzer settings during this test should be set for
average deviation, a 15 kHz low-pass filter, no de-emphasis, and no high-pass filter, if these settings
are supported.

This alignment can be done with either the R-2670 Communication Analyzer or the 8901_ Series
Modulation Analyzer. The method of choice is the R-2670 analyzer.

1. Initial setup using the R-2670 Communication Analyzer:

- Connect a BNC cable between the “DEMOD OUT” port and the “VERT/SINAD DIST/DMM

COUNTER IN” port on the R-2670.

- Press the

SPF

key on the R-2670 to display the “SPECIAL FUNCTIONS MENU.” Move the

cursor to “High Pass,” and select 5 Hz on the soft key menu. Select 20 kHz for the “Low
Pass” setting.

- In the “RF Control” section of the R-2670, move the cursor to the “B/W” setting and select

“WIDE +/- 100 kHz” on the soft key menu.

- Place the R-2670 cursor in the “Display” zone. Select “AC VOLTS” on the soft key menu.

Move the cursor to the “Range” setting and select “AUTO.”

2. Initial setup using the 8901_ Series Modulation Analyzer:

- Press the

FM MEASUREMENT

button. (The “

Error 0input level too low”

indication is

normal until an input signal is applied.)

- Simultaneously press the

Peak –

and

Peak +

buttons. Both LEDs on the buttons should

light.

- Press the 15 kHz LP filter key.

3. Select the

TX Deviation Balance

alignment screen. The screen indicates the transmit

frequencies to be used. See

,

,

,

and

4. In the "RF Control" section of the R2670, set the service Monitor to the desired frequency (as

shown in the frequency list in the TX Deviation Balance alignment screen).

5. Left-click the

PTT Tone: Low

button.

6. Left-click the slider of the frequency selected (should be the same frequency as step 4).
7. Left-click the

PTT Toggle

button on the screen to make the radio transmit. The screen

indicates whether the radio is transmitting.

8. Measure and Record the Low Tone Tx Deviation value from the 8901_ Series Analyzer or the

AC voltage value from the R2670.

9. Left-click the

PTT Tone: High

button.

10. Adjust the softpot value until the measured deviation/voltage, when using the high tone, is

/- 1.5% of the value observed when using the Low Tone.

«
...
76
77
78
79
80
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Explorer 1000 Pro

Бренд: Jackery Страницы: 40

Бренд: Onan Страницы: 16

Бренд: Probuilder Страницы: 110

Бренд: Generac Power Systems Страницы: 20

Бренд: Sandstrom Страницы: 92

Бренд: R&S Страницы: 81

Бренд: Exalt Страницы: 86

Бренд: Raymarine Страницы: 2

Бренд: Chevron Страницы: 26

Бренд: Xoro Страницы: 122

Бренд: MAJORITY Страницы: 24

Бренд: ILX Lightwave Страницы: 55

Бренд: Vertex Standard Страницы: 6

Бренд: Vertex Standard Страницы: 51

Digital plus LV200

Бренд: Lenz Страницы: 12

Бренд: Whisper Power Страницы: 46

Бренд: PowerTech Страницы: 8

Бренд: Coby Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды