manualshive.com logo in svg

Motorola APX 4000, Базовое руководство по обслуживанию

"Motorola APX 4000" - портативная радиостанция с уникальными функциями для безопасной коммуникации. Basics Service Manual доступен для скачивания бесплатно на manualshive.com. Идеальное решение для профессионалов в сфере коммуникации. Подробный мануал поможет настроить и использовать устройство эффективно и безопасно.

Поделиться
Скачать
background image

3-6

Basic Theory of Operation

: Controller Section

The ARM controller core of the OMAP processor handles the power up sequence of all devices, 
including firmware upgrades, and all operating system tasks that are associated with FLASH and 
SDRAM memories and user interface communication. The FLASH memory (64 MB) is required to 
store the firmware, tuning, and Codeplug settings, which upon initialization get read and stored into 
SDRAM (32MB) for execution. The ARM and DSP core jointly control and configure audio, wireless 
and RF devices linked to the Serial Peripheral Interface (SPI) and Synchronous Serial Interface 
(SSI) buses to enable radio FM and optional wireless communication protocols. For encryption, a 
separate ARM processor is used (MACE) to encode and decode encryption packets coming in from 
the main OMAP processor through the SSI interface. Its firmware is flashed via the main processor 
during an upgrade request to its internal FLASH memory. The MACE encryption processor is located 
on the keypad board.

The power and most clocks to the controller devices are provided by the MAKO IC and external 
switching and linear regulators on board. A Complex Programmable Logic Array (CPLD) IC divides 
the 24.576 MHz clock from MAKO to source OMAP's 32 kHz Real Time Clock, and MACE's 4 MHz 
main clock. OMAP's main clock is supplied externally from an on board 12 MHz crystal. 

The radio has two internal microphones and an internal speaker, as well as available microphone 
and speaker connections for external accessories. The internal 4 Ohm speaker is located on the 
same side as the main display and keypad of the radio. The internal speaker is driven by a Class D 
audio amplifier located on the main board that is capable of delivering a rated power of 0.5 W. The 
external accessory speaker is driven by a Class AB audio amplifier on the MAKO IC that is capable 
of delivering 0.5 W of power into a 16 Ohm as a minimum load. Both speaker paths use the CODEC 
for volume control and to convert the audio signal from digital to analog. Both internal and external 
microphones use the CODEC's ADC to deliver digital audio samples to the DSP controller. 

The user interface block consists of a main display, a keypad, top controls and the accessory side 
connector. The side connector (Universal Connector) provides audio, USB, RS232 communication 
for accessories. All signals to and from the connector go through the internal keypad board before 
reaching the microcontroller and other devices on the main board.

The radio also has integrated feature of Global Positioning System (GPS) and Bluetooth with Man-
down feature (depending on radio model) (see 

Figure 3-6

).  The GPS and Bluetooth Combo RF 

chipset (NL5500) is located on the Main board together with the GPS/RF Diplexer circuitry and 
Bluetooth Front-End circuitry.  The GPS receiver section of the GPS/BT combination IC interfaces 
with the OMAP processor through a dedicated UART port.  The GPS receiver also has a dedicated 
reset controlled solely by the OMAP processor. The GPS/Bluetooth IC (NL5500) taps the GPS signal 
from transceiver path and processes the location information before relaying to the OMAP processor 
via UART lines.  The clock supplies to NL5500 included a 26MHz TCXO and 32kHz clock from 
CPLD.

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Sangean WR-11BT Safety Instructions preview
WR-11BT
Бренд: Sangean Страницы: 13
Tecnoclima ENERGY 105 Assembly, Use And Maintenance Instructions preview
ENERGY 105
Бренд: Tecnoclima Страницы: 52
Keysight Technologies M9383B VXG-m Security Manual preview
M9383B VXG-m
Бренд: Keysight Technologies Страницы: 24
Protec 7021-8-9571 Instructions For Use Manual preview
7021-8-9571
Бренд: Protec Страницы: 64
Vidao PDV707KIT Instruction Manual preview
PDV707KIT
Бренд: Vidao Страницы: 16
EDIFIER TickTock MF240 User Manual preview
TickTock MF240
Бренд: EDIFIER Страницы: 6
C. Crane CC GOZO Instruction Manual preview
CC GOZO
Бренд: C. Crane Страницы: 3
Smart Cover ECC160 User Manual preview
ECC160
Бренд: Smart Cover Страницы: 12
ApexRadio 700DTA Quick Start Manual preview
700DTA
Бренд: ApexRadio Страницы: 2
Insignia NS-A2202 User Manual preview
NS-A2202
Бренд: Insignia Страницы: 102
TechniSat 0020/4995 Instruction Manual preview
0020/4995
Бренд: TechniSat Страницы: 224
SOUNDMASTER PDB-1800 User Manual preview
PDB-1800
Бренд: SOUNDMASTER Страницы: 73
SMC Networks SMCRPUPOE Specifications preview
SMCRPUPOE
Бренд: SMC Networks Страницы: 2
Acterna BN 2255/02 Operating Manual preview
BN 2255/02
Бренд: Acterna Страницы: 40
SOUNDMASTER IR4000DAB Instruction Manual preview
IR4000DAB
Бренд: SOUNDMASTER Страницы: 15
Mitsubishi Electric CQ-JB0160A Service Manual preview
CQ-JB0160A
Бренд: Mitsubishi Electric Страницы: 31
DUROMAX XP9HPE User Manual preview
XP9HPE
Бренд: DUROMAX Страницы: 64
DUROMAX XP8500E User Manual preview
XP8500E
Бренд: DUROMAX Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды