Motorola APX 4000 Скачать руководство пользователя

Страница: 414 / 526

6-14

Radio Alignment Procedures

: Transmitter Alignments

6.5.4

PA Saturation Reference Tuning

Tuning is done through

PA Saturation Referencing

screen.

1. Select the

PA Saturation Reference

alignment screen. The screen indicates the transmit

frequencies to be used. See

and

2. In Manual Mode, set the service Monitor to the desired frequency (as shown in the frequency

list in the PA Saturation Reference alignment screen).

3. Adjust the PA Saturation Reference softpot value with the slider until the radio transmits as

close as possible to the rated power. For rated power refer to the help text in the Tuner.

4. Left-click the slider of the frequency selected (should be the same frequency as step 2).
5. Left-click the

PTT Toggle

button on the screen to make the radio transmit. The screen

indicates whether the radio is transmitting.

6. Repeat the steps 2 to 5 for all frequencies.
7. Left-click the

Program All

button on the screen to dekey the radio and save the tuned values.

Figure 6-17. PA Saturation Referencing Alignment Screen (VHF)

Содержание APX 4000















































































































































































































































































































































































































































































































































Результаты поиска

Содержание APX 4000

Отзывы:

Похожие инструкции для APX 4000

Бренды по названию

Популярные бренды

Motorola APX 4000, Базовое руководство по обслуживанию

Результаты поиска

Содержание APX 4000

Отзывы:

Похожие инструкции для APX 4000

Бренды по названию

Популярные бренды