manualshive.com logo in svg

Motorola APX 4000, Базовое руководство по обслуживанию, Страница: 416 / 526

Поделиться
Скачать
Motorola APX 4000 Скачать руководство пользователя страница 416

6-16

Radio Alignment Procedures

: Transmitter Alignments

Figure 6-20.  PA Saturation Referencing Alignment Screen (700/800 MHz)

6.5.5

Transmit Deviation Balance Alignment

This alignment procedure balances the modulation contributions of the low- and high-frequency 
portions of a baseband signal. Proper alignment is critical to the operation of signalling schemes that 
have very low frequency components (for example, DPL) and could result in distorted waveforms if 
improperly adjusted.

This procedure needs to be performed at multiple frequencies to allow for proper alignment across 
the entire RF band. The RF band is divided into frequency zones with a calibration point (value) in 
each zone.

NOTE:

This alignment is required after replacing (or servicing) the main board.

Proper alignment requires a modulation analyzer or meter with a frequency response to less than 
10 Hz modulating frequency. The modulation analyzer settings during this test should be set for 
average deviation, a 15 kHz low-pass filter, no de-emphasis, and no high-pass filter, if these settings 
are supported.

This alignment can be done with either the R-2670 Communication Analyzer or the 8901_ Series 
Modulation Analyzer. The method of choice is the R-2670 analyzer.

1. Initial setup using the R-2670 Communication Analyzer:

- Connect a BNC cable between the “DEMOD OUT” port and the “VERT/SINAD DIST/DMM 

COUNTER IN” port on the R-2670.

- Press  the 

SPF

 key on the R-2670 to display the “SPECIAL FUNCTIONS MENU.” Move the 

cursor to “High Pass,” and select 5 Hz on the soft key menu. Select 20 kHz for the “Low 
Pass” setting.

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов