Motorola APX 4000 Скачать руководство пользователя | Manualshive

Страница: 512 / 526

background image

Glossary-4

Glossary

firmware

Code executed by an embedded processor such as the Host or DSP in
a subscriber radio. This type of code is typically resident in non-volatile
memory and as such is more difficult to change than code executed
from RAM.

FGU

See frequency generation unit.

flash

A non-volatile memory device similar to an EEPROM. Flash memory
can be erased and reprogrammed in blocks instead of one byte at a
time.

FLASHcode

A 13-digit code which uniquely identifies the System Software Package
and Software Revenue Options that are enabled in a particular
subscriber radio. FLASHcodes are only applicable for radios which are
upgradeable through the FLASHport process.

FLASHport

A Motorola term that describes the ability of a radio to change memory.
Every FLASHport radio contains a FLASHport EEPROM memory chip
that can be software written and rewritten to, again and again.

FMR

See Florida Manual Revision.

Florida Manual
Revision

A publication that provides supplemental information for its parent
publication before it is revised and reissued.

frequency

Number of times a complete electromagnetic-wave cycle occurs in a
fixed unit of time (usually one second).

frequency
generation unit

This unit generates ultra-stable, low-phase noise master clock and other
derived synchronization clocks that are distributed throughout the
communication network.

General-Purpose
Input/Output

Pins whose function is programmable.

GPIO

See General-Purpose Input/Output.

hang up

Disconnect.

home display

The first information display shown after a radio completes its self test.

host code

Object code executed by the host processor in an ASTRO subscriber
radio. The host is responsible for control-oriented tasks such as
decoding and responding to user inputs.

IC

See integrated circuit.

IF

Intermediate Frequency.

IMBE

A sub-band, voice-encoding algorithm used in ASTRO digital voice.

inbound signaling
word

Data transmitted on the control channel from a subscriber unit to the
central control unit.

Term

Definition

«
...
510
511
512
513
514
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Бренд: Galaxy Страницы: 38

Бренд: Goodmans Страницы: 12

Бренд: MULTIQUIP Страницы: 108

Бренд: InTouch Страницы: 39

Бренд: Winco Страницы: 13

Бренд: Pulsar Страницы: 26

Бренд: Clas Ohlson Страницы: 16

Бренд: Zebronics Страницы: 6

Бренд: LawnMaster Страницы: 34

Бренд: Vertex Standard Страницы: 4

Бренд: Vertex Standard Страницы: 31

Бренд: AWA Страницы: 25

Бренд: Toyama Страницы: 38

Бренд: Edwards Страницы: 33

Бренд: Bowers & Wilkins Страницы: 57

Бренд: Magnavox Страницы: 7

Бренд: PASCO Страницы: 9

Бренд: Brookstone Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды