Motorola APX 4000 Скачать руководство пользователя | Manualshive

Страница: 302 / 526

background image

6-12

Radio Alignment Procedures

: Performance Testing

6.6

Performance Testing

6.6.1

Bit Error Rate

This section describes the Bit Error Rate (BER) test of the radio’s receiver at a desired frequency
(see

).

6.6.1.1 Bit Error Rate Fields

Set up the R2670 Communication Analyzer as follows:

1. Connect the RF Input port of the radio under test to the RF IN/OUT port of the R2670 Service

Monitor.

2. Set up the R2670 Service Monitor:

- In the Display Zone, select PROJ 25 STD mode and set the meter to RF DISPLAY.
- In the RF Zone, configure the analyzer as follows:

- In the Audio Zone, select the 1011 Hz PAT code and set the deviation to “PROJ25Dev:

2.83 kHz ~”.

The bit error rate screen contains the following fields:

•

Rx Frequency

:

This field selects the Receive Frequency directly in MHz.

•

Test Pattern

:

This field selects the Digital test pattern to be received by the radio. Choices are: Standard Tone
Test Pattern (Framed 1011), F2 1031, Standard Interface Test Pattern (CCITT V.52) and Phase
2 Digital (1031 Hz) Test Pattern.

•

Modulation Type

:

This field represents the digital modulation type of the incoming signal on which BER is to be
calculated.

•

Continuous Operation

:

This field allows the user the option to repeat the BER test indefinitely. A selection of Yes will
cause the radio to calculate BER on a continuous basis and update the results on this screen
after each integration time. A selection of No will cause the BER test to execute for only one
sample of the integration time and then update the display.

•

Audio

:

This field allows the user to select the audio output during a test. Selecting Internal will cause
the radio's built-in speaker to unmute to any signals at the desired frequency which are present
during the test. Selecting External will route the same signal to the radio's accessory connector
audio output. Selecting Mute will disable the audio output.

NOTE:

There will be

no audio

option available for APX 1000 when performing a Bit Error Rate

Test.

RF Control:

Generate

Preset:

B/W: NB

Freq:

Test frequency (Ex: 851.0625 MHz)

Output Level:

-50.0 dBm

Gen RF Out:

RF I/O

«
...
300
301
302
303
304
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Бренд: Teac Страницы: 12

Бренд: Blaupunkt Страницы: 34

Бренд: Weelko Страницы: 13

HDG3000B Series

Бренд: Hantek Страницы: 102

Бренд: A2Z Ozone Страницы: 14

Бренд: C. Crane Страницы: 35

Бренд: LawnMaster Страницы: 28

LifeOX-AIR Ozzy

Бренд: Lifetech Страницы: 17

Бренд: Firman Страницы: 114

Бренд: Sunwave Страницы: 47

Бренд: Wiltron Страницы: 160

Бренд: ALL POWER AMERICA Страницы: 32

Бренд: Harman Страницы: 20

Бренд: PRESIDENT Страницы: 42

Бренд: Denver Electronics Страницы: 5

Бренд: Denyo Страницы: 47

Бренд: Denver Страницы: 2

Бренд: Denver Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды