Motorola APX 4000 Скачать руководство пользователя страница 468

Страница: 468 / 526

8-34

Disassembly/Reassembly Procedures

: Radio Reassembly

8.6.10 Reassemble the Accessory-Connector Cover (38)

1. Insert the hooked end of the cover into the pocket. Engage the hook beneath the undercut

and swing the cover down onto the radio. Ensure the cover is seated properly and the screw
is aligned into the threaded hole.

Figure 8-48. Engaging Hook and Seating Cover

2. Hand tighten the thumb screw clockwise until secured.

NOTE:

Do not overtighten the screw. The screw should be snugged and does not allow the
cover to move.

Figure 8-49. Securing the Cover

Top Hooked End

Thumb Screw

Thumb Screw with Hex Head Socke

Содержание APX 4000















































































































































































































































































































































































































































































































































Результаты поиска

Содержание APX 4000

Отзывы:

Похожие инструкции для APX 4000

Бренды по названию

Популярные бренды

Motorola APX 4000, Базовое руководство по обслуживанию

Результаты поиска

Содержание APX 4000

Отзывы:

Похожие инструкции для APX 4000

Бренды по названию

Популярные бренды