Motorola APX 4000 Скачать руководство пользователя | Manualshive

Страница: 241 / 526

background image

Chapter 8 Basic Troubleshooting

This section of the manual contains troubleshooting charts and error codes that will help you to
isolate a problem. Level one and two troubleshooting will support only radio alignment,
programming, battery replacement, and knob replacement, and circuit board replacement.

Component-level service information can be found in the “ASTRO APX 1000 Portable Radios
Detailed Service Manual,” Motorola publication number 68012004061.

8.1

Power-Up Error Codes

When the radio is turned on (power-up), the radio performs self-tests to determine if its basic
electronics and software are in working order. Problems detected during these tests are presented
as error codes on the radio’s display. For non-display radios, the problem will be presented at
power-up by a single, low-frequency tone. The radio should be sent to the depot if cycling power and
reprogramming the code plug do not solve the problem. The presence of an error should prompt the
user that a problem exists and that a service technician should be contacted.

Self-test errors are classified as either fatal or non-fatal. Fatal errors will inhibit user operation;
non-fatal errors will not. Use

to aid in understanding particular power-up error code

displays.

Table 8-1. Power-Up Error Code Displays

Error Code

Description

Corrective Action

01/02

FLASH ROM Codeplug Checksum Non-Fatal
Error

Reprogram the codeplug

01/12

Security Partition Checksum Non-Fatal Error

Send radio to depot

01/81

Host ROM Checksum Fatal Error

Send radio to depot

01/82

FLASH ROM Codeplug Checksum Fatal Error

Reprogram the codeplug

01/84

External EEPROM Blank (or SLIC failure) Fatal
Error

Send radio to depot

01/88

External RAM Fatal Error –

Note:

Not a

checksum failure

Send radio to depot

01/90

General Hardware Failure Fatal Error

Turn the radio off, then on

01/92

Security Partition Checksum Fatal Error

Send radio to depot

01/93

FLASHport Authentication Code Failure

Send radio to depot

01/94

Internal EEPROM Blank Fatal Error.

Send radio to depot

01/98

Internal RAM Fail Fatal Error

Send radio to depot

01/A0

ABACUS Tune Failure Fatal Error

Send radio to depot

01/A2

Tuning Codeplug Checksum Fatal Error

Send radio to depot

02/81

DSP ROM Checksum Fatal Error

Send radio to depot

«
...
239
240
241
242
243
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Бренд: Champion Страницы: 42

Бренд: ConcealFab Страницы: 22

Бренд: EGG Страницы: 52

Бренд: Promate Страницы: 23

Бренд: camry Страницы: 48

Бренд: Konig Страницы: 21

Бренд: All-Power Страницы: 14

Бренд: Audial Страницы: 23

Бренд: Tivax Страницы: 31

Warwick W-59-IP

Бренд: Fisher Страницы: 20

EDACS PRISM HP/LPE-200

Бренд: Ericsson Страницы: 104

Бренд: Sandstrom Страницы: 124

Бренд: Briggs & Stratton Страницы: 56

Бренд: Powermate Страницы: 16

Бренд: LENCO Страницы: 91

Бренд: Curtis Страницы: 1

Бренд: Midland Страницы: 3

Бренд: Midland Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды