manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 70

Injector

Function

To supply the correct amount of petrol at the right

timing.

Operation / Operating principle

Injector coil is excited for the petrol passage to

open.

Level in wiring diagram:

Coils and injectors

Location:

•

on the intake manifold

•

connector: on injector

Electrical characteristics:

14.8 Ohm +/- 5% (at

20 °C)

Pin-out:

"+": Supply:

" ": Ground connection

AXONE:FUEL INJECTION SYSTEM

AXONE: PARAMETERS

Injection time

AXONE: ACTIVATION

Left injector:

 Operation for 4 ms, 5 times

The auxiliary injection relay (No. 29 in the wiring diagram, placed on the front right side of the motorcycle,

in the auxiliary fuses/relays box, first relay to the left starting from the front; CHECK, however, the

identification of the relay with the colour of the cables) is energised for 5 seconds and the grey/red cable

of the injector is closed to ground for 4 ms per second. Disconnect the 4-way connector of the fuel pump

to be able to hear the relay and injector activation. The continuity of the wiring is necessary for correct

activation: no error indications are displayed in case of lack of activation

AXONE: ELECTRICAL ERRORS

Left injector

 

P0201

 - shorted to positive / shorted to negative / open circuit.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 28 of the BROWN con-

nector.

•

If shorted to negative: no voltage has been detected.

•

If the circuit is open: an interruption has been detected

Troubleshooting

Electrical system

STELVIO 1200 NTX

ELE SYS - 70

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды