manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 119

•

Undo and remove the five screws fixing

the alternator belt cover.

•

Remove the oil radiator lower support

bracket and the alternator belt cover.

Locking torques (N*m)

Alternator belt cover screw (radiator bracket
retainer) TCEI M6x40 (2)

 

10 Nm (7.38 lbf ft)

 

Alter-

nator belt cover screw - TCEI M6x16 (4)

 

10 Nm

(7.38 lbf ft)

•

Loosen the screw.

•

Loosen the nut and undo the set screw

so that the alternator slides down.

•

Using the belt tensioning tool, tension

the belt to the prescribed torque.

•

Tighten the set screw.

•

Tighten the lock nut.

Specific tooling

020677Y

 

Alternator belt tensioner, Belt ten-

sioning lever

Locking torques (N*m)

Belt tension

 

50 Nm (36.88 lbf ft)

STELVIO 1200 NTX

Engine

ENG - 119

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды