manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 158

Crankcase - crankshaft

Removing the crankshaft

•

Remove the clutch.

•

Remove the tone wheel and the oil

pump gear.

•

Working from the generator side, un-

screw and remove the nut.

•

Remove both gears.

•

Remove the connecting rods.

•

Undo and remove the eight fixing

screws and collect the washers.

•

Hold the crankshaft during flange re-

moval.

•

Using the suitable special tool, remove

the crankshaft flange.

•

Remove the sealing ring from the

flange, if necessary.

Specific tooling

12.91.36.00

 

Tool to remove the flywheel-side

flange

Engine

STELVIO 1200 NTX

ENG - 158

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды