manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 236

•

Remove the exhaust end.

Removing the manifold - tail pipe

•

Remove the exhaust end and the ex-

haust manifolds.

•

Remove the starter motor protection in

order to disconnect the lambda probe

connector.

•

Unscrew and remove the nut and re-

move the fixing screw.

•

Remove the manifold - exhaust end

coupling together with the lambda

probe.

See also

Removing the exhaust manifold
Removing the tail pipe

Removing the exhaust manifold

The engine and the exhaust system components get very hot and remain in this condition for a certain

time interval after the engine has been switched off. Before handling these components, make sure that

you are wearing insulating gloves or wait until the engine and the exhaust system have cooled down.

Chassis

STELVIO 1200 NTX

CHAS - 236

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды