manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 43

•

Clamp the clutch pipes with the clutch

switch and the left light switch, making

sure that the fixing part of the lower

clamp faces the inside, to avoid that by

turning the steering the instrument

panel is damaged and the clamp gets

unhooked.

FRONT SECTION

TABLE B

•

Pay attention to the longer cable (1),

which is to be placed to the left, while

the shorter cable (2) is to be placed to

the right.

TABLE C - HEADLIGHT AND TURN INDICATOR

SYSTEM CLAMPS

•

Clamp the right headlight cable (1) and

the right turn indicator (2).

STELVIO 1200 NTX

Electrical system

ELE SYS - 43

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды