manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 47

TABLE E - BATTERY COMPARTMENT HOUS-

ING

•

The battery housing must be free of

any connections or pipes, in order to

allow perfect fitting.

Back side

CAUTION

ONCE THE ELECTRICAL SYSTEM IS REFITTED, THE CONNECTORS RECONNECTED AND
CLAMPS AND RETAINERS RESTORED, CARRY OUT THE CHECKS INDICATED UNDER "SPE-
CIAL CHECKS FOR THE CORRECT CONNECTION AND LAYING OF CABLES" IN THE "ELEC-
TRICAL SYSTEM INSTALLATION" SECTION.

REAR SECTION

TABLE A - CORRECT FITTING OF THE ODOM-

ETER CLAMP

•

The clamp fixing the odometer cable

must be placed ahead of the brake pipe

guide clamp.

REAR SECTION

TABLE B - FITTING THE FAIRING COMPART-

MENT LID SAFETY RELAY

•

Lay down the main system and clamp

the stop switch system, odometer sen-

sor and fall sensor to the system. Be

careful that the latter does not come

into contact with clips.

•

Attach the relay to the support plate

and fix it keeping the main system be-

tween the plate and the mudflap.

•

Connect the recharge cable and place

it as in the photo.

STELVIO 1200 NTX

Electrical system

ELE SYS - 47

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды