manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 239

•

Undo and remove the two radiator up-

per screws and collect the washer.

•

Remove the oil cooling radiator.

Installing

•

Fit the oil cooling radiator on the vehi-

cle following the operations described

in the removal chapter but in reverse

order.

•

Pull out the oil filler plug / oil level dip-

stick (1).

•

Pour new oil until it goes over the min-

imum level marked "MIN" on the dip-

stick (1).

•

Insert the oil filler plug / oil level dipstick

(1).

•

Start the vehicle and let the engine run

for a few minutes so that the oil circu-

lates and fills the radiator internal

ducts.

•

Stop the engine and check the oil level

with the dipstick (1).

•

Fill with engine oil as required.

STELVIO 1200 NTX

Chassis

CHAS - 239

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды