manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 143

•

Partially fit the service shaft closing

cap.

•

To screw the cap until it stops, use two

M6 flanged screws larger than the orig-

inal screws.

•

Tighten the two M6 flanged screws op-

erating in stages until the cap stops

against the crankcase.

•

Undo and remove the two M6 flanged

screws.

•

Tighten the cap with the two original

TBEI screws.

Installing sliders

•

Fit the crankshaft and the service shaft

on the crankcase.

•

Fit the fixed chain sliders and tighten

the fixing screws.

•

Tighten the chain caps with O-rings.

•

The operations related to the movable

chain sliders are described in the cyl-

inder fitting section.

See also

Installing the crankshaft
Installing the service shaft

STELVIO 1200 NTX

Engine

ENG - 143

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды