manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 153

•

Check that the oil in the left cylinder

chain tensioner has been drained off

by compressing it. If the operation is

difficult, use a pin drive to push the

central hole so that the oil is drained off

from the circuit.

•

Fit the chain tensioner in the cylinder.

•

Lubricate the piston and the cylinder.

•

Lock connecting rod motion with the fork tool.

•

Using the suitable piston ring clamp tool, place the cylinder and fit the chain in the timing

system plate.

CAUTION

DURING THIS OPERATION, PAY ATTENTION NOT TO DAMAGE THE PISTON.

Specific tooling

020674Y

 

Piston ring clamp

020716Y

 

Connecting rod locking

•

Fit the movable chain slider.

•

Fit the upper gear.

•

Fit the chain tensioner cap temporarily

and keep the chain taut on the service

shaft.

STELVIO 1200 NTX

Engine

ENG - 153

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды