manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 167

•

Remove the nipple - oil pump fitting.

•

Bring the left cylinder piston to the TDC

in combustion phase.

•

Mark a reference on the oil pump con-

trol gear and another on the driven

gear so as to place them correctly

again upon refitting.

•

Unscrew and remove the nut on the

crankshaft.

•

Remove the oil pump control gear.

•

Screw the nut again so that the internal

shim washer does not fall in the crank-

shaft crankcase.

•

Unscrew and remove the driven gear

nut.

•

Collect the washer.

•

Remove the oil pump driven gear.

•

Remove the driving pin.

STELVIO 1200 NTX

Engine

ENG - 167

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды