Moore Industries NET Concentrator System AOM Скачать руководство пользователя страница 88

Страница: 88 / 103

NET Concentrator System

NCS

- 88 -

Moore Industries-International, Inc.

www.miinet.com

Installation

Installation consists of physically mounting the unit,

completing the input connections, and grounding the

unit.

The Interface Module and external I/O modules

connect together via DB-25 connectors integrated into

the side(s) of each module.

Mounting

The NET Concentrator System Modules are designed

to snap easily onto 35mm Top Hat (EN50022) DIN-

rails.

Snap any I/O modules onto the DIN-rail to the right of

the Interface module, then slide it along the rail until

the DB25 connectors on the side of the I/O module

connect completely with the unit to its left.

Making the Electrical Connections

Refer to specific m odule sections for detailed terminal

designations and connection figures.

Contact/Load Suppression

(applies to Relay Output Module only)

When the ROM outputs are used to switch external

relay coil, contactor, solenoid or some other inductive

load, large voltage spikes may be created in nearby

cable harnesses. When excessive, these voltage

spikes can disrupt the operation of all nearby

electronics including this product. Please follow

the external relay manufacturer instructions for their

recommended relay coil suppression kits. Inductive
loads should have suppression devices installed on

the relay right across the relay coil itself. Usually this

is a simple diode for dc circuits. AC circuits routinely

use an R-C snubber.

Recommended Ground Wiring
Practices

Moore Industries recommends the following ground
wiring practices:

• Any Moore Industries product in a metal case

or housing should be grounded.

• The protective earth conductor must be

connected to a system safety earth ground
before making other connections.

• All input signals to, and output signals

from, Moore Industries’ products should be

wired using a shielded, twisted pair wiring

technique. Shields should be connected to an
earth or safety ground.

• For the best shielding, the shield should be

run all the way from the signal source to the
receiving device (see Note below).

• The maximum length of unshielded input and

output signal wiring should be 2 inches.

Note:

Some of Moore Industries’ instruments can be

classified as receivers (AIM, TIM, etc) and some

can be classified as transmitters (AOM, ROM, etc).

Hence, your shield ground connections should be

appropriate for the type of signal line being shielded.

The shield should be grounded at the receiver and

not at the signal source.

Hot Swapable I/O Modules

Should an Input/Output module need to be replaced,

simply program a new module, remove the old

module from the mounting base and snap in the

new one. For more specific instructions, see

Hot-

Swapping an I/O Module

the in

I/O Modules Section

of this manual.

Содержание NET Concentrator System AOM








































































































Результаты поиска

Содержание NET Concentrator System AOM

Отзывы:

Похожие инструкции для NET Concentrator System AOM

Бренды по названию

Популярные бренды

Moore Industries NET Concentrator System AOM, Руководство пользователя

Результаты поиска

Содержание NET Concentrator System AOM

Отзывы:

Похожие инструкции для NET Concentrator System AOM

Бренды по названию

Популярные бренды